2007 Chevrolet Silverado 2500 HD 2WD. 2x Front Wheel Hub Bearing -515098. 2x Front Inner Tie Rod End -ES3488 2x Front Sway Bar End Link -K80631 2x Front Outer Tie Rod End -ES3609 2x Front Lower Ball Joint -K6693 1x Pitman Arm - With 4 Grooves - Heavy Duty -K6536 2x Front Upper Ball Joint -K6696 1x Front Steering Idler Arm -K6535 1x Idler Arm Bracket Assembly And Grease Hose -K6723. Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts.
Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.
Suspension Control Arm Replacement Guideline. Control arms are installed in pairs on the front and rear axle and connect the chassis to the wheels as part of the suspension. Therefore, they have a significant influence on the driving characteristics of the vehicle.
A dynamic or a comfortable driving style? The control arms are individually adjusted to the vehicle depending on the desired characteristics.
They also absorb lateral movements and forces resulting from driving off and braking. A defective control arm can manifest in the following ways. Increasingly woolly and imprecise steering. Tip:If the control arm is in working order, it is possible to only replace the defective bearings and joints. However, replacing bearings, control arm bushings and ball joints can be very complex and costly. First lift the vehicle using a car lift, ideally a wheel-free four-post car lift. This makes it easier to correctly tighten the control arm fixing screws. WARNING:Depending on the axle design, the control arm may need to be secured against falling with a suitable device, e. Treat the fixing screws and nuts of the control arm with rust solvent and leave it to work for a few minutes so that they are easier to loosen. On vehicles with automatic headlight levelling, it may be necessary to detach the leveling sensor from the control arm. If the stabilizer is connected to the control arm, the next step is to loosen and remove the corresponding stabiliser fixing screws. Loosen and remove the control arm fixing screws. Loosen the ball joint at the steering knuckle with a suitable special tool e. Remove the old control arm. Clean the mounting flange of the ball joint pin on the steering knuckle with sandpaper and then with brake cleaner. Otherwise single rust particles can enter the new control arm joint via the ball pin, potentially leading to premature failure of the joint. Fit the new control arm with the supplied accessories and attach new fixing screws and nuts. Reattach the stabilizer and, if applicable, the leveling sensor for headlight leveling to the control arm. NOTE:Do not tighten the fixing screws and nuts in this step, otherwise the rubber mounts will twist when the suspension compresses. This would lead to undesired preloading onf the mounts. Now lower the vehicle until the suspension is compressed.Depending on vehicle type, load or unload the vehicle until the required height published in the specific installation instruction is reached. This is where a wheel-free four-post car lift is advantageous, as the underside of the vehicle can still be easily accessed once lowered. Lower the vehicle all the way.
Measure the chassis and adjust if necessary. If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Raise the vehicle and remove the front wheels.
To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Remove the bad or worn ball joint from the control arm.
Loosen the compression ball joint on the steering knuckle using a suitable special tool. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. Measure the chassis and adjust it using the various holes on the compression ball joint if necessary.Finally, carry out a test drive. How will I know that I have to renew my ball joint parts? If your ball joint fails, you will listen to a strange sound while driving. And that sound may help you to realize that your ball joint has failed and you have to renew them.
What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel.
Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car.
Are worn ball joints dangerous? Yes, it can be quite dangerous. Because, a worn ball joint causes suspension damage, inspection failure, and breakage of related parts. It might make your front suspension come apart while driving, so the wheels move in whatever direction inertia takes them.
That can lead to a fatal accident. What happens if I don't replace ball joints? If you don't want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension.
However, you do not need to change the ball joints if it is new. Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation.Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. 515098, ES3488, K80631, ES3609, K6693, K6536. K6696, K6535, K6723, anti sway bar, anti roll bar. Has ABS with tegral Sensor.
If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. ECCPPAUTOPARTS has the final power of interpretation of all the above Targeted Discount Terms and Procedures. Virgin Islands, Northern Marianas, Guam are not deliverable. ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. ECCPP 2 Pcs Wheel Hub Bearing Front For Buick LaCrosse Century Regal Lesabre FWD. Universal 12V Low Pressure 5-9 PSI Electric Fuel Pump Installation Kit E8012S. Front Wheel Hub Bearing For Chevy Monte Carlo Impala Cadillac Eldorado DTS FWD. Coilovers Suspension Kits For 1986-91 Mazda RX-7 FC3S 2D 1.3L Shocks Adj.Taillight Assembly Red Right Passenger Side For 2017 2018 2019 Ford Escape Kuga.