2x Front Wheel Hub Bearing -515054. 2x Front Inner Tie Rod End -ES3488. 2x Front Lower Ball Joint -K6541.
2x Front Outer Tie Rod End -ES3493T. 2x Front Upper Ball Joint -K6540.
1x Front Steering Idler Arm - Heavy Duty -K6534. 1x Pitman Arm - With 4 Grooves - Heavy Duty -K6536. 2x Front Sway Bar End Link -K8987. Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts. Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page.
In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods.
Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. Picture(A) Note: Cleanliness is extremely important when working on the power steering.
Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. Lift the vehicle and dismount the front axle wheels.
Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Dismount the front underride guard. Loosen the fastening nut from the tie rod and remove it completely. Remove the tie rod end from the steering knuckle using an appropriate ball joint separator.
Remove the clamp of the bellow on the steering gear. Push the bellow towards the tie rod end. Unscrew the inner tie rod from the rack. Clean the sealing face of the bellow at the steering gear. Clean the lug of the rubber contact surface of the ball joint in the steering knuckle.
Note:Always use new self-locking nuts and bolts for a reliable repair. Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance.
Secure the ball joint in the steering knuckle and mount the nut. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure.
Tip:Secure the ball stud against twisting with a suitable tool. Mount the front underride guard. Align the wheels and adjust them if necessary. What are the symptoms of a bad sway bar?
Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. What happens when a sway bar breaks? Because a sway bar helps the car's suspension to put more pressure on loaded springs, a broken sway bar means that the car's suspension will not be able to handle corners as well or as quickly.
While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Sway Bar Stabilizer Link Replacement Guideline.While driving, the following signs may indicate a faulty sway bar stabilizer link: (1). Rattling and thumping noises on rough roads. Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below.
Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove.
Tip:If the ball stud also starts to turn, hold it with a suitable tool. Press stabilizer link out of torsion bar.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Press stabilizer link at suspension strut out of bracket. Insert new stabilizer link at suspension strut. Insert new stabilizer link at stabilizer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension.
Conclude with a test drive. Why should I get my tie rods inspected on a regular basis? If you don't get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for.
If your vehicle pulls to one side while driving, or when braking, it's possible that bad tie rods may be the culprit. Your vehicle's tires will also show uneven wear on the inside and outside edge of the tire when there's a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation.
Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive.
Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them.
Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty.
Raise the vehicle and remove the front wheels. To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Loosen and remove the fixing nut of the ball joint on the steering knuckle.
Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Remove the bad or worn ball joint from the control arm. Loosen the compression ball joint on the steering knuckle using a suitable special tool. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts.
Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. Finally, carry out a test drive. How will I know that I have to renew my ball joint parts? If your ball joint fails, you will listen to a strange sound while driving.
And that sound may help you to realize that your ball joint has failed and you have to renew them. What happens if a ball joint breaks?
When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. Broken ball joints will seriously affect the steering and suspension.It can even result in your wheel falling off the car. Are worn ball joints dangerous?
Yes, it can be quite dangerous. Because, a worn ball joint causes suspension damage, inspection failure, and breakage of related parts. It might make your front suspension come apart while driving, so the wheels move in whatever direction inertia takes them. That can lead to a fatal accident. What happens if I don't replace ball joints?
If you don't want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new.
Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation.
Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. 515054, ES3488, K6541, ES3493T, K6540. K6534, K6536, K8987, anti sway bar, anti roll bar.
Has ABS with tegral Sensor. If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. ECCPPAUTOPARTS has the final power of interpretation of all the above Targeted Discount Terms and Procedures.Virgin Islands, Northern Marianas, Guam are not deliverable. ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. Front Or Rear Wheel Bearing Hub For Buick Rendezvous Lesabre Chevrolet Impala. Pair Front Or Rear Wheel Hub Bearing For Chevy Impala Pontiac Grand Prix Venture. For 1988-98 Chevy GMC 1500/2500/3500 Towing Manual Side View Mirrors Truck Pair. For Freightliner Cascadia 08-16 LH+RH Side Hood Black Power Heated Mirrors pair. For Nissan Rogue Sport 2019 2020 Remote Keyless Entry System KR5TXN3 4 Buttons. Piston Installer Pliers Ring Spreader Installation Expander Tool 3/16" to 1/4". This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Steering & Suspension\Tie Rods & Steering Linkages". The seller is "eccppautoparts" and is located in this country: US. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech Republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South Africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi Arabia, United Arab Emirates, Qatar, Kuwait, Bahrain, Republic of Croatia, Malaysia, Brazil, Chile, Colombia, Costa Rica, Dominican Republic, Panama, Trinidad and Tobago, Guatemala, El Salvador, Honduras, Jamaica, Antigua and Barbuda, Aruba, Belize, Dominica, Grenada, Saint Kitts-Nevis, Saint Lucia, Montserrat, Turks and Caicos Islands, Barbados, Bangladesh, Bermuda, Brunei Darussalam, Bolivia, Ecuador, Egypt, French Guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman Islands, Liechtenstein, Sri Lanka, Luxembourg, Monaco, Macau, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Vietnam.